产品详情
查看大图

  • 产品名称：韩国DACELL显示仪表DN500A/DN510A

  • 产品型号：DN500A/DN510A
  • 产品厂商：韩国大拿DACELL称重传感器
  • 产品价格：0
  • 折扣价格：0
  • 产品文档：
你添加了1件商品 查看购物车
简单介绍：
韩国DACELL显示仪表DN500A/DN510A TANK, DRUM OR CAN FILLER, HOPPER, CHECKER, LIMIT SCALE etc.
详情介绍：
韩国DACELL显示仪表DN500A/DN510A
DN500A, 510A
TANK, DRUM OR CAN FILLER, HOPPER, CHECKER, LIMIT SCALE etc.


 
 
  • SPECIFICATIONS
ANALOG INPUT AND A/D CONVERSION
Load cell excitation 10VDC±5%, 320mA
Input Sensitivity 0.45㎶/D
Zero adjustment range -0.6mV~42mV : combinations of 6bit dip switch
Input voltage Max. 32mV
impedance 10㏁ (Min.)
noise 0.6㎶p.p or Less
A/D converter type : dual slope type
resolution : 1/65,000 counts(16bits)
converting speed : 20times/sec
Non-linearity 0.01% of full scale
Temperature-drift zero ±20PPM/℃
span ±20PPM/℃
Overload tolerance 10% of full capacity
Display update rate 20 times/sec

DIGITAL SECTION
Display unit 12.7mm(1/2"), 7digits
Annunciators steady, zero, tare, gross, auto, print, hold
Decimal point position 0, 0.0, 0.00, 0.000
Keyboard ten key, zero, tare, tare reset, print, gross/net, grand total,
sub total, parts, number, hold, reset, auto, code, s/n&enter
DN510A : run, standby, sp1, sp2, sp3, sp4
External input signal opical-isolator
min. Division x1, x2, x5, x10, x20, x50
max. Display 550,000
Rear panel Loadcell input : 5pin connector
External control : 5pin input terminal (zero, tare, tare reset/hold/print, gross/hold reset/subprint)
DN510A : control relay : 7pin terminal

GENERAL
Data memory back-up appr. 10year
Power 100/110/120/220/240V AC, ±10%, 50/60㎐ (factory preset)
Power consumption appr. 10w
Operating condition temperature : -10~40℃ (14~104℉)
humidity : 85% Rh Max. (non-condensing)
Net weight 2.3kg
Gross weight 3.0kg
Physical dimensions (WxDxH) 192x150x96mm / (WxDxH) 7.56x5.91x3.78inch
Fuse 250V/0.3A

 
  • FEATURES
  • Control for PACKER, FILLER, HOPPER, CHECKER, LIMIT SCALE etc.
  • Auto span calibration
  • 50 kind of parts number can be memorized
  • Watch-dog function installed for diagnostics
  • Data memory back up for over 10years
  • Front display window is covered by lexan film for the protecting of dust
  • Lock function for the protection of set-up mode
  • Weighting judgment by over & under setting when printer is connected
  • Three kinds of hold function (peak-hold and average-hold, auto-hold)
  • Weight memory back up for up to 10years
  • Can drive up to 8pcs of load cell (350Ω)
  • Serial interface standard installed (RS-232C and CURRENT LOOP)
  • Can print the data & time, count, parts number, weighing decision and sub/grand when printer is connected by option
DN 500A
  • The external field switch can be directly connected to 5pin terminal located at the rear panel for the remote control of some key-board functions (ZERO, TARE, TARE RESET, HOLD, HOLD RESET, PRINT, SUB PRINT, NET/GROSS)
DN 510A
  • The external field switch can be directly connected to 5pin terminal located at the rear panel for the remote control of some key-board functions (START, STOP, ZERO, TARE, TARE RESET, HOLD, HOLD RESET, PRINT, SUB PRINT, NET/GROSS)
  • 4 Step control (SP1, SP2, SP3, SP4)
  • 6 control relay built-in (SP1, SP2, SP3, SP4, FINISH, NEAR ZERO)
  • Relay output mode (LIMIT, PACKER, CHECKER1, CHECKER2)
Option
OP1 Printer I/F : Centronics Parallel
OP2 Analod Out : V - out(0~10V)
OP3 Analod Out : I - out(4~20mA)
OP4 Serial I/F : RS 422, RS485
OP5 BCD Out-put

 
  • DIMENSIONS
产品留言
标题
联系人
联系电话
内容
验证码
点击换一张
注：1.可以使用快捷键Alt+S或Ctrl+Enter发送信息!
2.如有必要,请您留下您的详细联系方式!

沪公网安备 31011402005142号